Essential Information About Wavlink AX1800 WiFi Range Extender

The Wavlink AX1800 extender model comes under the WIFi 6 series. When you connect this device to your house network, then you can remove all the dead zone areas of your office and house. The interesting fact is that you can do the configuration process of this Wavlink extender by the WPS method. Let’s read this entire page, without skipping any steps to learn the full information about the Wavlink AX1800 device.

Wavlink AX1800 Extender Benefits

Enjoy fast internet speed in outdoor areas.
Wavlink AX1800 extender comes under the efficient cost.
Kick-off all the dead zone areas.
Increase the strength of host router WiFi signals.
Easily connect with any existing router device.

Visit Wavlink AX1800 Web Management Page:

At the start of this process, connect Wi-Fi-containing gadgets with the Wavlink extender by ethernet cable. After that, open a navigation and enter wifi.wavlink.com web gateway in the URL bar. Next, fill in all the credentials shown on the web management page. Therefore, the Wavlink extender login process is now done without facing any trouble with the help of this method.

Do Wavlink AX1800 Extender Setup

There are two methods to do the setup process of the Wavlink AX1800 WiFi range extender.

By WiFi Protected Setup Button-

When you pair your Wvlink AX1800 extender with the router by this method, then make sure your router must have the WPS button. If it does not have this button, then skip this step.

First, place the Wavlink AX1800 device power plug in a wall socket.
After that, wait for a few minutes to see the extender LED indications start blinking.
Now, verify that your Wavlink AX1800 device must be placed closer to the host router device.
Next, press the Wavlink extender and host router WPS button for a short while.
Further doing this the WPS LED starts blinking solid blue on both the WiFi gadgets.

Configure Wavlink AX1800 On Web

Try this method, if your router does not support the WPS button or if you fail after trying the above method.

In the beginning, settle both the extender and the router power plug in a power socket.
Then, join your computer, laptop, PC, etc to the extender network by wired or wireless method.
For the wireless connection select the WiFi network from the WiFi list and enter the security password in that field.
For a wired connection, take an ethernet cable and connect one end to the extender ethernet port and another end to the WiFi gadget ethernet port.
Now, to access the setup page, launch any latest version of a web browser on your device.
After that, write the web portal or IP address of the Wavlink extender in the URL bar.
Ultimately, the login page will open up on your display.
As of now, fill in the login credentials. (If you don’t know the details check the tag of your Wavlink AX1800 extender device).
Further, pick the WiFi network that you want to extend the range of the network.
In the end, the Extender successfully connected to the router notification will show on your display.

After doing the Wavlink extender login process if you are facing any kind of issue then you will need to observe the below solution tips to fix the extender issue.

Resolve Wavlink AX1800 Extender Setup Issues

Verify the gap between the AX1800 extender and the host router.
Turn On/Off your Wavlink AX1800 device.
Check the position of the Wavlink extender device.
Remove all additional gadgets from the list of Wavlink extender networks that are not in use.
Swap all the damaged wires with new ones.
See the LED status of the Wavlink extender device.
Perfectly located the Wavlink extender power plug in an electrical socket.

After trying the apart seven solutions, if the extender issue is not resolved then try out the lower advanced troubleshooting tips.

Download The Latest Version Of Wavlink AX1800 Extender Firmware

Due to the outdated firmware of the Wavlink AX1800, you can face trouble later doing the configuration process of your Wavlink extender device.

First, go to a search engine.
Now, enter the web portal of the Wavlink extender in the address bar.
After that, go to the settings, and fill in all the credentials which are shown on the login page.
Next, choose the administration option, and after that select the extender software upgrade option.
In the end, wait for a few minutes to download the upgraded Wavlink extender firmware file on your WiFi gadget.

Reset Your Wavlink WiFi Extender Device

Try this last method to fix the extender issue.

First, grab a paperclip.
Now, look for the reset hole button. (Reset hole button is located at the backside of the Wavlink AX1800 extender)
Next, for around 10 seconds push the Wavlink extender reset button.
After that, all the Wavlink extender device LEDs will turn off.
Therefore, it means your device is completely reset now.

Note: After doing the Wavlink extender reset process, you will need to do the configuration process again.

With the guidance of this page, you will learn the basic information such as the login and setup process of the Wavlink AX1800 extender device. If you are still facing any issues after trying the Wavlink extender solution tips then contact our Wavlink team experts.